Wear Knowledge Of Diamond Grinding Blocks

Diamond grinding blocks have different degrees of wear at different stages and different forms of wear. Generally speaking, they can be divided into micro-broken abrasive grains, abrasive grains falling off, overall abrasive grains, abrasive grain flattening, and macro-broken abrasive grains. The degree of wear and tear varies. After research, it is found that there are many factors that affect the wear condition, which are not only determined by the material properties, specifications, and grinding conditions of the grinding wheel, but also have a profound impact on the preparation method of the grinding wheel. Another factor depends on the quality of the diamond. The diamond grinding block has very complex tribological characteristics in the process of grinding. The diamond chips are driven by the cutting fluid to erode the surface of the bond, forming erosion marks on the surface. The bond is abraded under conditions similar to fluid grinding. The crescent craters on the front of the diamond show erosion caused by fluid cavitation during sawing.


The abrasive wear in the stable stage is mainly friction wear, but in the transition stage, since the grinding wheel has just been trimmed, the abrasive grains stick out to the maximum, and many abrasive grains do not participate in cutting, so the proportion of the overall abrasive grains is higher than that in the stable stage. Relevant personnel have studied the diamond grinding block and believe that the actual wear process of diamond needs to go through different paths. The longer the overall abrasive particles on the research surface remain, the easier it is to process, and the higher the wear resistance of the tool. After the tool uses the cutting function for a long time, the abrasive particles are naturally dull and the efficiency is reduced.

TransGrind is a professional manufacturer of diamond tools for concrete or stone floor, we have supplied many different kinds of diamond tools for many customers, such as Scanmaskin tools, Lavina tools, Klindex tools, Husqvarna tools, HTC tools etc. And we got many good feedbacks from our customers about our premium quality. Welcome to consult for our products by clicking the below picture to get into our official web if you are interested.




Comments

Post a Comment

Popular posts from this blog

How to renovate the old cement floor

Image
  How to renovate the old cement floor: 1. Use a professional floor grinder , install the grinding disc , and grind the ground . Remove all the sand from the surface to reveal smooth and firm aggregates. 2. With the sealing curing agent, sprinkle it on the ground, let it fully absorb until it is saturated, which can increase the strength of the cement floor. 3. If the cracking of the cement floor is serious, first roughen the floor, and then rinse the floor with a water gun. 1. Construction joints shall not be left in the laying of the cement concrete surface. When the construction gap exceeds the allowable time, the joints should be treated. If the concrete floor is seriously sanded and ash, the water grinding machine should be installed with a diamond grinding block first. The purpose is to smooth the ground, remove the glue, paint, plain cement slurry and other attachments on the ground, and then assemble the diamond grinding block with a water grinder to grind the ground to
Read more

Grinding Features

Image
Grinding is a method of cutting a workpiece with a grinding wheel as a cutting tool on a grinding machine. The features of this method are: (1) Since the abrasive grains of the grinding wheel have high hardness and heat resistance, grinding can process materials with high hardness, such as hardened steel and cemented carbide. (2) The characteristics of the grinding wheel and the grinding machine determine that the grinding process system can perform uniform micro-cutting, generally ap=0.001 ～ 0.005mm; the grinding speed is very high, generally up to v=30 ～ 50m/s; the grinding machine has good rigidity; using hydraulic transmission, so grinding can economically obtain high machining accuracy (IT6 ~ IT5) and small surface roughness (Ra = 0.8 ~ 0.2μm). Grinding is one of the main methods of finishing parts. TransGrindTools manufacture wide range kinds of diamond grinding tools which can make your grinding work easier and more effective. ​​ (3) The temperature of the grinding zone
Read more

The Origin and Evolution Process of Concrete Floor

Image
Concrete floor  is a kind of integral ground that uses cement and stone particles as the main material. In the course of China 's ground development, it has successively experienced such forms as   terrazzo floor , fair-faced concrete floor ,   and colored wear-resistant floor . Still fashionable terrazzo floor Terrazzo has the strength, wear resistance and durability of natural stone, and it is smooth, easy to clean, and good integrity. As the indoor floor of a large number of public buildings, it is practical and beautiful. The new type of terrazzo has new developments in color and pattern. The decorative effect can meet the modern aesthetic needs, and it can also meet the requirements of environmental protection. It is safe and non-toxic, does not release harmful substances such as benzene, formaldehyde, and has no radioactivity. In addition, compared with building materials with similar effects, decoration investment can be saved by 2/3. Many universities and hospitals use terr
Read more